There are two main adhesives for tiles in the bathroom :
– Normal ;
– Elastomeric .
Clay select depending on the base , which is lined , the material from which made tiles, specificity operating surface. How to put the tiles in the bathroom.
Average consumption of glue for wall -1.5 kg/m2/mm . Accurate information each manufacturer takes depending on the size of the teeth on a grater . The more expensive glue , the less fuel it . That is, that is not always cheaper , it economical. Ceramic tiles in the bathroom.
Lay out the tile after previous measurements basics. The rule is simple : try to avoid drastic than half tiles. It is desirable to have a project sweep the walls with tiled layout .
The tiles can be cut on a special machine , or using power tools with diamond wheels .
Remember that the tiles on the wall must go to the tile on the floor . Therefore, we first lay out the tiles on the floor. Choosing ceramic tiles for the bathroom.
Very often (especially in larger rooms ) after tiled walls floor tiles destroyed. Therefore devised a way to laying tiles on the wall starting from the second row . Instead, the first row of tiles horizontally to fasten the wall base ( plank profile of drywall construction ) for the second row because the tiles can crawl . How to choose the right shower tray for small bathroom.
1. wall
2 . Paul
3 . Ceramic floor tiles
4 . Planck or profile of CC design
5 . The second row of wall tiles
Making laying tile with remote crosses , trying not to leave the glue in the joints . Given that the basis of our smooth, toothed trowel adhesive is applied to the tile or the wall or floor. When pressed tiles. Teeth .. ” glue creeping , forming a continuous layer, but consider that having a grater with 5 mm teeth , glue between the tile and the wall is 2.5 mm. Accordingly, when the teeth 3 mm – 1.5 mm glue But not all manufacturers allow following minimum thickness. Most adhesives has recommended application thickness of 2 mm. Good result for filling glue gives grater with rounded teeth. Steps ideas renovation bathroom decor without cost.
Of course , it is important and quality tiles . This also depends on the width of the seams. By the way , the seams between the tiles have not only a decorative function. They also perform the function of joints . When the temperature changes , like any other material , tiles also resized . The idea of the layout of the small bathrooms.
After drying, the adhesive joints between the tiles will be overwritten by a fugue . Preparation and application of technology to the grout seams again each manufacturer is different. Also, not all manufacturers recommend priming his fugues . So, carefully read the instructions. Draw fugu squeegee angle forty-fifth to the seam . Waiting for a specified term, wash off the remnants of the Fugue on a tile with a sponge float or spongy , frequently changing the water , also under a 45 ° angle to the seam . Interior design small bathroom.
For interior and exterior angles manufacturers offer variety final foxes ( profiles). Some artists are able to undercut the outer corners at 45 °. Everything depends on the design and quality of tiles. Inside corners recommend not fill fugue , and silicone sealant ( there is a spectrum of colors ) , especially when our walls with plasterboard . Change part of the broken tiles.
Holes in the tile , for example under the socket, cut or diamond cutters. Put tiles on the floor throughout the plane , including a bathtub.
Often installed in bathrooms ladder. This is convenient , but you should remember that it should always be with a little water .
Depending on the project , in the bathrooms , you can perform a variety of materials and finishes are not necessarily all wall tiles.
Again I remind you that when in a wet basement ceiling made of drywall , ventilation should work to extract not only moist air from the premises , but also between the plasterboard ceiling and the existing overlap (eg , concrete panel ) . bathroom renovation ideas for tight budget .
Installing a bath or shower tray is made after the laying work .
I do not recommend to plug “on forever,” these devices .
With acrylic products easier .
As for metal baths and shower trays offer to make special places “nest” and mount them on a cush (eg polyurethane foam) . Under the metal bath have to be ventilated space .
Sanitary appliances ( shower tray , bathtub, sink, toilet, bidet) after installation at points of contact with the tile is sealed with silicone sealant .
Making laying tiles in the bathroom , proceed to putty and paint .
main adhesives for tiles in the bathroom
- Cast iron cookware without coating
- Restoration bath home by yourself
- Terms conditions contract sale real property by installments
- Mortgage: mortgage lending new practice
- Wireless Internet Advantages wireless network
- How to fix a hole in drywall ceiling
- Repair of the balcony slab Reinforcement of the balcony slab
- How start a business with little money
- How To Hang Drywall Ceilings [video]
- Restoration and repair of chipped enamel tubs or sinks