Home >> DIY Plumbing Repair >> Connecting the toilet to the sewer

Connecting the toilet to the sewer

Connecting the toilet to the sewer

Can I get a connection to the sewer toilet independently, without involving professionals plumbers ? Special skills to carry out such work is required, and thus is familiar with the basic wiring, you can start working on their own. It is important to note that the process of installing a toilet technology does not depend on which of the premises of his place – in the bath or in the house. Read more about the process – in our article on the outdoor toilet.


What is required for installation

Wiring diagram assumes the toilet to the sewer when connecting the toilet to the sewer pipe to use eccentric or pleated cuffs , plastic taps and sewage pipes . The appearance of the toilet bowl with the sewer pipe goes well with the toilet bowl , which takes a holistic view of the sanitary unit. However, we must remember that when installing a toilet with sewage pipes have a number of requirements:

they can not be cut ;
you can not change their geometry.

At the same time implementing the toilet connecting the hands , be aware that the corrugated cuff can be bent at any angle and extend along the length , and the eccentric sleeve can be rotated on their axis to compensate for deviation from the alignment of the connected plastic tube .

Sewer connection

Connecting a toilet with a corrugated tube

Technology connection process is as follows:

Corrugation to connect the toilet is inserted into the sewer pipe . Place docking lubricated with silicone.
The toilet is connected to the second bellows portion , carrying out , thus, its connection to the pipe. Check the reliability of the connection – dial tank or pour a bucket of water and poured into the bowl. The audit closely monitored for leaks .

Determine the location for drilling, fastening to hold the toilet to the floor anchors .
Toilet set aside and drill a hole in the planned areas.
Insert dowels .
Install a toilet on a stationary position and is connected corrugated pipe sealant inside greased . Connecting to the toilet riser is accompanied by checking the reliability of the connection. If there is no water leaks and water runs normally, fix all the screws that were included with the toilet bowl.

After fixing the toilet is necessary to check its stability. If the toilet after him sit down man , prone to swing , you have to dismantle it and run the device under the cement screed .
Installing the toilet ends sealed his place docking with the tile using a sealant or silicone.

how to Install New Sewer Lines in Existing Drains

Connecting the toilet without the use of corrugations : Basic Rules

If you decide not to use the flute , are very useful basic rules by which it is performed in such a case, the connection :

If the toilet is connected without corrugations , it is necessary to use a nozzle which is also known as an adapter or sewer pipe. Connection adapter in this case is carried out differently depending on the angle which has a toilet. We differentiate between three options:

WC connection with an oblique issue – it is being installed in the floor – this attitude is no longer relevant, although in the last century is very widely used ;
if the release of the toilet vertical, then the installation is carried out at an angle of 90 º to the wall ;
if the release of the toilet horizontal, then the installation is carried out in a wall at an angle of 30-40 º.

In that case, if the release of the toilet does not match the release of sewage network , you will have to choose another model or toilet , or apply a certain angle bent – pipe adapters .

Now consider the detailed features of each type of plumbing installation .

Such models are widely used in European countries. This is largely due to the fact that in such sanitary devices mounted downwardly directed outlet and a siphon located in the toilet bowl . This design allows you to put the toilet to the wall at any angle. Installation with this is simple:

after marking on the floor set a standard screw flange , equipped with lock ;
Located in the center of a circular hole flange mounted sewer pipe ;
a flange mounted on a toilet bowl is rotated until it locks ; outlet having a special sealing ring is pressed in this connection automatically to the end of the sewer pipe .

Particular attention should be paid to securing the toilet to the floor. Typically , the legs of the bowl with horizontal outlet equipped with special holes that are designed to hold the device to the floor.

Installation of the toilet , equipped with an oblique issue

Technology of this type of toilet assembly as follows:

Before installing your toilet to the sewer , the toilet issue with an arrangement of the grooves smeared with red lead mixed with linseed oil .
Top strand is wound resin . At the end of this process 0.5 cm should remain free (otherwise ends strands fall into the hole and will contribute to contamination) .
Wrap the strand too carefully smeared with red lead .
Next, perform the assembling of the toilet , fixing the final process of the sewer pipe into the socket .

Thus, we examined how to connect the drain bowl of your application to the sewer pipe. Thanks to the information The installation itself practicable . In addition , while you can save money. However, if you feel that your existing skills is not enough to perform such work , yet economical to use the services of professionals.

Connecting the toilet to the sewer

Tags: , , , , , ,

Leave a Reply

Your email address will not be published. Required fields are marked *