Main menu

Pages

Ariston washing machine error codes

 Decoding the error codes Ariston washing machine. A description of each error code problems and methods, Error codes Ariston and Indesit washing machines with control system EVO-II device and repair of electronic controller. Error codes and troubleshooting description Indesit washing machines, Ariston. How to decode the error code.


Error Codes Bosch washing machine and the corresponding fault

Error Codes Bosch washing machine and the corresponding fault -All modern automatic washing machines of the brand Bosch, equipped with digi..


Ariston washing machine error codes In the category Error Codes Many people are interested in knowledge and learning about many subjects, this knowledge may be vital at some point in your life, attention enough, and dive into more detail in regards to Ariston washing machine error codes.


LG washing machine error code-LG Front Load Washer Error Codes

Error codes when repairing washing machines LG Consider basic mistakes, FE error means that the water level in the tank, E3 error-occurs wh...


Decoding the error codes Ariston washing machine. A description of each error code problems and methods, Error codes Ariston and Indesit washing machines with control system EVO-II device and repair of electronic controller. Error codes and troubleshooting description Indesit washing machines, Ariston. How to decode the error code, if there is no display. A table of error codes for washing machines of different brands. Also provides background information on Ariston washing machine error codes. In order to diagnose failures and Ariston Indesit washing machines do not cause special problems, we give below error codes for these machines.


why do not rotate the drum in the washing machine

If the drum in your washing machine isn’t rotating, it could be due to several reasons: Power Issues and Motor Problems  Check if the machi...


Ariston washing machine error codes


Identifying Hotpoint or Indesit Error Codes


ariston washing machine error code F03-F04


Hotpoint Washing Machine F01 H20 H2O repair


Flashing Lights on Washing Machine How to Repair


hotpoint ariston wmg 642, F05 error fix


What do the error codes Indesit washing machines

What do the error codes Indesit washing machine ?-Indesit washing machines are considered to be of sufficient quality and, with proper main...



Ariston Washing machine error codes displayed when an one way or another. The washing machine itself tells you the cause of the malfunction. You only need to correctly decode the error code. Table with decoding the error codes usually have all the instructions for operating the washing machine. But often, after the expiration of the warranty, we don’t save this documentation. And she can easily get lost.


Ariston Washing machine error codes displayed when an one way or another. The washing machine itself tells you the cause of the malfunction. You only need to correctly decode the error code. Table with decoding the error codes usually have all the instructions for operating the washing machine. But often, after the expiration of the warranty, we don’t save this documentation. And she can easily get lost.


washing machine error codes


And at a time when you need to look at the table of codes, this statement under the hands may not be. Below you can see the table of error codes Ariston washing machine.

Samsung Washing Machine 3E Error Code not spinning

Maytag Washer not draining code F02 or F2

Whirlpool Washing Machine Won´t Spin F06 error code

How to fix LG washing machine LE error code

Haier Washing Machine Error Codes

Washing Machine Diagnostic Test & Error Codes

With its help you can decipher the code as well as view the causes of faults and how to eliminate it.

F01

Short circuit in the motor drive control circuit SEE

1. Check possible water entering the electronic controller connector contacts, from which comes a tourniquet on the drive motor.

2. Sequentially replace the electronic controller (managing TRIAC drive motor) and the drive motor.

F02

Signal from the Tahoe-sensor on the rotation of the drive motor is not getting to the electronic controller

1. Check whether blocked rotor drive motor, due to jamming drum bearings SEE or for other reasons.

2. Check the reliability of the electrical connections between the electronic controller and the drive motor.

3. Check the resistance of the windings Tahoe-generator (must be 115.170 OM to SEE controllers equipped with EVO-I).

4. In the case of the use of asynchronous motor drive, SEE check connectors and the wiring harness between the controller and motor.

5. Consistently replace the drive motor and electronic controller of washing machine Ariston.

F03

Faulty temperature sensor or relay “zaliplo water heating Elements

1. Check reliability of connections between electronic controller and temperature sensor.

2. Check electric resistance temperature sensor (should be about 20 kΩ at 20° c).

3. Consistently replace temperature sensor and electronic controller

F04

Defective water level switch (pressure switch)

Water level sensor simultaneously generates signals “OVERFLOW” and “EMPTY TANK” (although it should be only “EMPTY TANK”). In this case, the tank is filled with water up to the level, SEE the “OVERFLOW”. The result is that at the same time included Bay (open water valves) and water discharge (drain pump). In this case:

1. Check the reliability of the connection between electronic controller and level sensor, and the sensor.

2. If these steps did not reveal the faulty element, point to replace the level sensor and electronic controller.

F05

Drain pump is not working or does not form part of the level sensor signal “EMPTY TANK” after running water drainage mode

1. Check the reliability of the connection between electronic controller and drain pump.

2. At the time of the alleged inclusion of the drain pump check for voltage on his contacts.

3. If this does not occur, check the pump itself (by submitting to it 220), its connectors, and an electronic controller.

4. Check the level sensor, as well as its connection to the electronic controller.

5. Check the filter and drain hose for the presence of blockages.

6. Consistently replace pump, pressure switch, the electronic controller.

F06

Bug buttons

The code is displayed, SEE “family Ariston Dialogic” (AD)

1. Check for contact in connectors and wiring between the controller and the control panel.

2. Check up serviceability of toolbar buttons.

3. Consistently replace Control Panel and an electronic controller.

F07

HEATER heat water not immersed in water

To SEE the EVO-II controllers:

1. Check connectivity between the contacts of the connector and electronic controller and

level sensor.

2. Check up serviceability of the level sensor.

3. Check up serviceability of Petn, by measuring its resistance (between pin 5 and 6 of the connector J3): for example, Petn power 1800 W it should be around 25 ohms.

4. Consistently replace TENG, level sensor and electronic controller.

To SEE with EVO-i:

1. Inspect the wiring and the presence of the contact in the connector Then the controller.

2. Check up serviceability of the relay HEATER on the controller.

3. Replace the electronic controller.

F08

Relay water heating Elements “zaliplo” (with an empty tank) or water level sensor generates signals simultaneously “OVERFLOW” and “EMPTY TANK” (“stuck” in the “EMPTY TANK”)

1. Check the water level sensor (switch).

2. Check the connection to the electronic controller is recommended, if necessary, replace the HEATER or level sensor.

3. If the faulty elements have been identified, replace electronic control.

F09

Failure (error) nonvolatile memory ESPPZU

1. Replace the electronic controller or replace/overwrite the non-volatile memory chip.

F10

There are no signals from the level sensor (tank is not empty but not complete)

To SEE the EVO-II controllers:

1. Check connectivity between the contacts of the connector I electronic controller and sensor level.

2. Check the level sensor: closed PIN. 2-4 connector J3 match as “EMPTY TANK” PIN. 2-3-“FULL TANK” PIN. 2-1-“OVERFLOW”.

3. Consistently replace the level sensor and electronic controller.

To SEE with EVO-i:

1. Check the contact in the connector, SEE the electronic controller.

2. Check up serviceability of sensor level, as well as the integrity of the wiring from it to the electronic controller.

3. Replace the electronic controller.

F11

Missing link about the health of the drain pump (pump is loose or torn his winding)

To SEE the EVO-II controllers:

1. Check the reliability of the connection from pin. 8 and 9 of connector J9 (or pin 1 and 2 of connector J15 if CM has the function of Easy Door) electronic controller and to the drain pump.

2. Check the correctness of the drain pump. Resistance of the winding must be approximately 170 m.

3. Consistently replaced drain pump and an electronic controller.

To SEE with EVO-i:

1. Check the integrity of the contacts of connectors CN1 and CNF on the electronic controller.

2. Check up serviceability of sensor level and drain pump.

F12

There is no connection between the display and electronic controller

To SEE the EVO-II controllers:

1. Check the integrity of the connection between connector J11 electronic controller and display.

2. Consistently replace electronic controller and display module.

To SEE with EVO-i:

1. Check SMS connectors electronic controller.

2. Other actions similar to those listed above.

F13

Defective circuit temperature control drying (for CM “Margarita 2000” with dryer, EVO-I)

1. Check the connection between the connector CAN electronic controller and temperature sensor drying.

2. Check up serviceability of drying temperature sensor and an electronic controller (replacement).

F14

Dryer does not turn on (SEE “Margarita 2000” with dryer, EVO-I)

1. Check the connection between the electronic controller and HEATER drying.

2. Check HEATER for drying and an electronic controller (replacement).

F15

Dryer does not shut off (SEE “Margarita 2000” with dryer, EVO-I)

1. Check the contact in the connector CN1 on the midplane.

2. Check and if necessary replace the level sensor and connector cost.

F17

The hatch door not closed or opened (SEE function with Easy Dorr, EVO-II)

1. Check the presence of voltage (220 v) between pins 3 and 4 connector J4 electronic controller (not in STANDBY mode), and also between the PIN. 3 and 5 door lock lock.

2. Check the triggering micro door switch (when door closed) on the PIN. 1 and 2 of connector J4 electronic controller.

3. Check reliability of lock door lock door.

4. If necessary, replace the door lock and electronic controller.

The hatch door not closed or opened (to SEE without the Easy Door controller EVO-II)

1. Check for AC voltage 220 in between contacts 1 and 3 m connector electronic controller (not STANDBY mode only), as well as between PIN. 1 and 3 door lock lock.

2. Check reliability of lock door lock door.

3. If necessary, replace the door lock and electronic controller.

F18

Microprocessor error

1. Replace the electronic controller

Ariston Washing Machine Arwxf129w, Ariston Washing Machine Problems, Beko Washing Machine Error Codes, Bosch Washing Machine Error Codes, Hotpoint Ariston Washing Machine, Hotpoint Washing Machine Error Codes, LG Washing Machine Error Codes, Whirlpool Washing Machine Error Codes.