Remove the polystyrene slabs and keep its ceiling

Remove the polystyrene slabs and keep its ceiling – In addition to improved interior design by renovating the ceiling, off polystyrene slabs should be as clean as possible. The preferred material to easily get the job done , the method used for removing tiles , as well as different finishes will be described. So you can make savings on your budget while following the trend in decorating with personalized redevelopment.

Renovating an old basement ceiling tiles polystyrene is often hard work . As the polystyrene slab rests on the ceiling is prohibited by insurance in case of fire insurance, it is suitable for those who wish to renovate their ceiling to ensure several areas. You need to start by removing the tiles while avoiding up leaving adhesive residue and the establishment of the new ceiling depending on the chosen material.

the preparation

Before anything else, we advise you to remove fragile and imposing objects in the room to work and still cover the ground newsprint or plastic. This precaution prevents you work extra cleaning and facilitates the collection of debris fell from the ceiling like glue residue and ends of slabs. For reasons of hygiene and safety , wearing a mask is highly recommended to protect against noxious odors, sometimes toxic .

For the realization of your tasks, you ‘ll need to protect yourself by following adequate material hardness slabs and where they are stuck . In general , you need a scraper, a knife to strip a palette knife or spatula type putty knife. In any case , you should always take into account the strength of the glue that holds the different slabs of polystyrene ceiling trying first on a small area to avoid mistakes in the way of detaching slabs . If burrs were made , they can take the filler stakeholders using the coating.

Tips easily removable polystyrene slabs

To put a ceiling in the standards and improve its design , renovation should be done especially for polystyrene slabs , the first step is to cleanly remove waste polystyrene tiles from the ceiling. For slabs glued on plain concrete or brick, it is convenient to use the stripping knife with a hammer as a chisel to a better distribution of the applied force. In that it is glued to the slabs of plastic, it should be heated beforehand with a heat gun starting from a corner before removing the slabs with a spatula .

If the tiles remain sharply after these few moments of trial , it means that the adhesive used to bond the tile was certainly very strong. Therefore , it is need to hire a professional to not take in a coup glue and plaster especially the services of a plasterer prove much more expensive .

Methods effective to release the adhesive layers

Once the tiles removed, the ceiling may still have some glue residue whose removal depends on the texture and material of support. A plaster ceiling does not support a vigorous scraping off the risk of the whole. It just should heat the glue residue with a heat gun . A more radical trick is to use a steam wallpaper stripper that exudes a high enough heat to soften the leg. Then comes a spatula to remove the glue. It is therefore essential to protect your hands and eyes as well as increase the risk of burns during the operation.

At the cost of slightly increased physical exertion, use a scraper sleeve-shaped and composed of a relatively thin blade ensures a clean finish fairly thin layers of glue . However , the application of a coating layer if necessary layers of paint or plaster depart . The use of solvents for removing adhesive residue raises cons -indications due to their high toxicity . Although acetone to produce a very significant returns , it is also recognized for its harmfulness, is an extremely dangerous chemical for health especially if inhaled . We therefore recommend the use of a device or a mechanical process.

Place the new ceiling surface

A perfectly flat , level surface without glue residue and coating should be covered directly to the installation of a glass cloth or a layer of wallpaper of your choice. If irregularities are noticed , they should be close by asking a non-woven or perform sanding . A white primer then supports a surface coverage by the wallpaper. As for the gap surfaces , display of the coating is still the best way to recap .

Generally, cleats often meet level problems . For this purpose , the fixing battens followed by setting different levels allows the location of the plasterboard . In the end, you’ll have a new and horizontal ceiling. If weight problems arise with respect to the joists , simply screw your cleats on these media so they do not present a risk of collapse . Each batten is so screwed on multiple joists and installing a plasterboard for cladding is facilitated .