How to connect the sink itself
So how to connect the sink can be yourself, then call the professionals to do the job is not necessary. The exception is if you have absolutely no experience in such work , and you are unsure of their abilities. Usually this work is done when the repair is coming to an end. Technology installation and connection as in the bathroom sink ( basin ) and the kitchen ( sink ) is identical , so we will not make a distinction between them in this article.
Preparing to Install
Determining the height of fixing a sink
Common shell that is not equipped with additional accessories , fixed at a height of 850 mm. At this level, draw a horizontal line, which corresponds to the level of the upper surface of the sanitary unit.
If there is a pedestal ( support leg ), or if the sink is mounted in the locker , secure shell height need not be determined – it will depend on the height of the legs or height tables.
Marks on the wall fixing points
Wiring diagram shell includes a number of markup before install fasteners. The connection ends bowl sink has mounting holes . With a sink to the wall and align it with the upper edge of a line marked on the wall , mark the position of places in which to perform the mounting holes in the wall. It is more convenient to carry out this work together.
In this case, one person holds the sink in the marked line and the other at the time the bottom marks the spot where it will be fixing. If there is a foot or reference case, the execution of the installation is simplified – sanitary unit is mounted on a support and mark out the attachment .
Installing a Vanity and Sink
Mounting fixtures
Mounting fixtures perform as follows:
Markings on the drilled holes in the wall .
Pegs hammered into them .
Screwed mounting studs .
Connecting the sink in the bathroom and the kitchen is to use expansion bolts , threaded bolts and nuts, plastic liners , which come complete with sink. When tightening the bolts should pay attention to the fact that the depth of screwing it possible to hang the sink and tighten the retaining nut that is protruding from the wall studs should be part of a length slightly greater than the thickness of shells plus 1.5 cm for tightening the nut.
Connecting to the water basin
installation mixer
In carrying out the connection sink in the kitchen or bathroom faucet installation can be done and is attached to the wall of the shell , however , it is recommended to carry out this work up front – before fixing the sink , so all the connections and fixtures are made from the bottom.
The mixer is installed in the following order:
The mixer is screwed fastening pin or two , depending on its variety.
Install hoses for hot and cold water , tighten them using the open-end wrench , tighten spend cautiously with moderate force , given the fact that the installation of faucet on the sink tighten them tighter fail.
Wiring diagram washing involves performing hoses , which will be supplied water through the holes in the sink.
Mounting studs on the back of the worn rubber seal , pressing plate and baits nuts .
Fixing nuts are tightened using a wrench.
Securing the sink on the wall
After connecting to the water sink can be mounted :
Sink with mixer tap fortified put on the mounting studs screwed into the wall.
Insert the plastic liners .
Tighten the nut.
Connecting the kitchen sink with a pedestal or base tables are beginning to install it on the supporting elements .
Connecting hoses for cold and hot water to the water supply system
Between the tap and the nut must be installed to seal the gasket. Thus Tighten the nut is not recommended. Rubber seal typically provides a good seal with the nut can be tightened after the test is performed , i.e. , after the inclusion of water. The leak at the connection nut must be tightened more tightly .
Connecting to the sink drain
Once the water supply is connected , it is necessary to carry out the connection to the sink drain. Begin this work with a set siphon. It is recognized that the presence of a special opening for overflow protection , suggests that a siphon off more pipes for water overflow . The shape of the siphon is made as S- shaped , and a bottle-shaped .
Connecting to the sewer cleaning is carried out as follows:
In the sink outlet siphon inserted and fixed it.
To fasten siphon tube ( either with a rigid angle, or corrugated ) .
Screwed pipe is inserted into the sewer issue . In the case where the diameter of output significantly exceeds the diameter of the pipe coming from the siphon , it is necessary to use an adapter , which is called sealing cuff ( made of rubber) , and well seal the tube.
Next, you need to check all connections for leaks .
important Notices
The comments are worth considering before starting work :
To connect the kitchen sink to the sewer system is not recommended Tighten all connections with the key , as this may damage the seals of rubber and waste the time and effort.
When you check the density of connections between the cuff and a drainage pipe water trickling stream , you have to remove the cuff , wipe surfaces that are to be joined , and then lubricate dry sealant cuff and make the connection again .
When connecting a double sink to use a special trap with access to the two pipes .
Performing simple rules , no doubt, will help everyone concerned to establish the owner of the house in the kitchen sink or in a bathroom without calling a plumber . You can connect a sink to drain, and bring it with running water faucet is mounted independently.
How To Replace a Drop-In Kitchen Sink
http://www.youtube.com/watch?v=qBXJ_9Yh__U
- How To Unclog a Sink Using a Drain Snake
You know that drain cleaners and solvents should only be used as last resort when it comes to unclogging drains. But, do you … - How to Unclog a Bathroom Sink with a Snake
This video will show you how to remove a pop-up stopper and unclog a bathroom sink with a drain snake (or cleaning cable) - How to Work a Snake for a Clog in a Sink : Home Sweet Home Repair
Working a snake for a clog in a sink is a process that will vary depending on the configuration of the pipes in question. Work a … - best way to snake a kitchen sink drain
you have to get a good snake down the vertical drain in wall best to remove pipe so your close to pipe in wall for easy snaking. - How To Unclog kitchen sink using a Drain Snake, tips & demo on BrassCraft Drum Auger
This video is intended for the novice DIY mechanic. Thus, we don’t go over how to take the plastic pipes apart in the video and …
How to connect the sink itself
- Instructions on how and with what tool you can cut the height of the interior door
- Panel curtains in interior design
- Steel doors pros and cons
- Appliance Repair Miami Beach Refrigerator Repair Miami Beach Review
- How to improve the radio reception
- Insurance property Insurance apartment or house
- What debts can be liquidated bankruptcy
- Comparison of Samsung Galaxy S4 and S3
- Cost of replacing windshield
- What material is best for walls
