Main menu

Pages

Construction framing baths

 If you have decided that you urgently need a room, and a project for the construction of the bath log home you do not end up like it ( you have no experience of such construction or did you just not enough money) , then you can choose the easier option of building baths, which involves the construction of bath on frame technology .


Construction framing baths



Today it is the frame construction technology have attracted many private traders , because the buildings, constructed using this technology have a number of advantages:


due to design features frame-type structures , such structures are characterized by its lightness and therefore do not require the installation of a powerful foundation;

again thanks to the carcass structure baths of this type are well trained to be warm ;

framed building is being built fast enough and still have the opportunity to decorate a bath at the same time inside and outside;

Well , finally , the construction cost of frame technology is much lower than the cost of other types of buildings.


Construction framing baths



How to choose a corner bath for small spaces


This article will try to address some specifics of how the construction of the framing bath with his hands.


Regarding layout, then the area steam must correspond in size 2.5×2.5 m, because if less steam will , it will be very inconvenient . When you plan the waiting room area and washing compartment , then count it so that you can place a bench to rest, as well as walk-in shower .


The foundation baths

Since the chosen frame structure is characterized by its ease , the foundation can be made at the simplified scheme. A good option for this building may be the most usual pier foundation with asbestos cement pipes , which are filled with concrete .


In order to produce such a foundation we need:


four-meter diameter asbestos cement pipe hundred millimeters (several dozen) ;

drill a hole  a depth of about five feet in diameter and 200 mm ;

cutting the tube into two equal parts and to insert them into the well and to fill them around the sand. The sand is then thoroughly compacted .


In order to make the solution for the fill pipe must use the following proportions :


take a bucket of cement (best brand M200 ) ;

about four buckets of sand ( well screened ) ;

seven or eight buckets of gravel ( fine ) ;

Water – as needed .


Construction framing baths



Best Bathroom Designs For Small Bathrooms Review


The resulting mixture should fill in all the pipes installed in the well.

Bottom rail baths

To make the bottom plate frame you will need several boards ( circumcision ) with a cross section 150×50 mm. Boards need to put together one with the other. Once binding is made in it for future logs slam floorings . Logs are made from the same boards as the piping . Be sure to make a good waterproofing of this part of the building. To do this, a harness and, of course , under Floor joists must enclose sections of roofing material . The segments should be approximately 200×200 mm .


In order to give the design strength , logs and piping can be attached directly to the foundation tubes with metal plates ( pre- immured in them) . Build the frame structure to be treated with a special solution , preferably more than once. The solution will help to protect the wood from insects and rot.


walling

Walling framing  bath with his hands is good because you can manually calculate the time for all the work and make the necessary breaks. For example, if time permits then before to build the walls , it is better to give all the materials prepared (even Cutting board ) a little lie down and thoroughly dry.


Further, according to the project of the boards need to make special frame racks , as well as some necessary details of all our roof truss construction .


After installation location is marked frame struts can begin final assembly frame walls.


Installation is recommended in the following sequence :


First you need to install two corner posts, and just a few intermediate ;

then the selected angle can begin sheathing leaf frame oriented strand boards (boards should be put on a level and secured to the frame using screws ) ;

then you need to install a few more studs that should also be sheets of OSB sheathing .


Assembly of the design as a whole is by gradually adding studs to the racks of new OSB .


Roof framing baths

In the process of construction framing baths all truss designs are collected from a single template on the ground, and then alternately raised to the roof. Further , each placed over the frame counter.


Before rising last farm on it is placed to form sheets of OSB gables . In order to make it easier to carry out assembly operations it is recommended to lay on the beams of the usual time- overlapping planks .


As for the roof , it is better to do a ventilated . To do this, the space between the rafters  necessary to lay special film , and the very stuff crate on board. It is best to stop the election on such material for the roof , as ondulin .


Once completed roofing and closed pediments ( sheets of OSB ) , you only need to install windows and doors in prepared openings.


finish baths

Rough ceiling is better to make using the same sheets of OSB , which need to be fixed on the bottom floor beams . For ceiling insulation should be laid not less than three layers of the selected insulation, which should also be formatted sheets with dimensions – 50x600x100 mm . In the area where it is supposed steam room, a pier to the insulant should also add a special ” soft ” foil , and the rest of the walls close glassine .


You can then pull the board used as forests ( pre- need to turn them over to the right side ) and then nail them to the joists . For steam usually choose regular oven , stove with a heating boiler , installed by the changing room . In order to comply with all the requirements of fire safety, the part of the wall that shuts off the steam room lounges, you need to put standard building brick .


As already mentioned, the construction of frame type can be immediately and finish the outside and inside. Therefore, during the breaks can be prepared skeletons of partitions, and then knocked at their blockhouse ( in the lounge ) or the lining (preferably made ​​of wood ) in the remaining rooms . Waiting room is equipped with ceiling hatch with a ladder to access the attic.


You can also lower the ceiling in a steam bath to 2.1 meters. This maneuver will allow it to warm further and upholster lime lining . Also recommended that the board of lime manufacture and shelves for the steam room .


If you make a bath with your hands and you have one helper , the maturity construction will take about as much time :


production of foundation – three days ;

Device Sill , log, erection of walls and Floor Covering – three days ;

immediate installation of trusses, laying a protective film , and installation crates – two days ;

the construction of the roof, wall decoration, installation of doors and trim the gables – two days.


It turns out that all the work ( not taking into account the internal and external finishes ), you will need approximately ten working days. It appears, framed bath with his own hands built not too long as it may seem at first glance.


Construction framing baths In the category Design houses Many people are interested in knowledge and learning about many subjects, this knowledge may be vital at some point in your life, attention enough, and dive into more detail more articles and learn more information about Construction framing baths.

Comments

table of contents title